![]() ![]() Keep a proper screwdriver / hex key with you at all times and check the tightness of the bolts every 50 – 100 arrows fired. This goes for bolts attaching the stirrup, the prod to the stock, the quiver mount, and everything else that you attached yourself. If you see any dirt in the rail, get rid of it before you apply any lubricant.Always perform this step after coming back from a hunting trip.The only way to cock the trigger requires the safety to be off & then switched on once the string is drawn. Take a good 2 to 3 minutes to do this one properly. Anyone got any experience/info with/about one of these pls Trigger mechanism seems to be all there, but I think has been incorrectly (re)assembled. Make sure to get rid of any dirt and dust that might be stuck inside the rail and in any possible nook, groove, or connection point. ![]() I recommend using compressed air in a can for this one. You don’t need to do this one often, just whenever you notice your vision starts to get obstructed or if you accidentally leave a fingerprint on the lens. Ideally, you should use lens cleaning wipes for this purposes so as not to smudge the lens. I recommend always keeping a backup string with you whenever you are shooting, just in case. If you forget to regularly wax your string, you can expect its lifespan to be cut down by about 20%. Depending on the type of crossbow you get, a string can last for anywhere between 200 and 1,000 arrows fired. If you start noticing any breakage or obvious separation of the serving, replace the string. Periodically check the bowstring for any signs of wear or separation of the serving, especially in the center where the arrow is nocked. Splintering or bending of arrow shafts.Loose bolts wiggle the riser/limbs (prod) to see if it moves independantly from the stock.This is a must-do, and it should become a habit before every shooting session, be it target practice or a hunting trip. Inspect Your Crossbow & Arrows Before Shooting If you have a compound bow, apply some lubricant to the wheels/axles as well to make sure they turn as smoothly as possible. The goal of the latter is to protect the bolts from corrosion and damage due to weather conditions. You’ll want to apply one or two drops of lubricant to the trigger box, as well as onto any visible mounting bolts, such as the ones connecting the riser with the stock. Lubricating The Trigger Box & Exposed Mounting Bolts (19) 19 product ratings - Barnett Crossbow Bolts 17035 Aluminum Pistol Arrows - Pack of 4 32.00. Apply two drops of lubricant to the middle of the rail and spread it across the entire length of the rail with your finger.Once applied, rub in the wax using your fingers the generated heat will melt it so it sticks for longer.ĭoing this will provide for much smoother traction of your bolt with minimum friction, substantially increasing accuracy.Apply the wax to the length of the string/cables, except for the part that’s right above the arrow rail, as it will gum up the trigger box.You should always check the instruction manual that came with your x-bow and see what is the manufacturer’s recommended waxing frequency. How often you should apply the wax depends on the type of crossbow (compound? recurve?) and the materials used. You will want to wax the string, as well as the cables in the case of a compound crossbow, on a fairly regular basis. Typically you will get a tube of wax with your crossbow package, but if you don’t make sure to buy some. Below is a list of things you should do to keep your weapon in tip-top working condition. Nothing could be further from the truth failing maintain your crossbow properly will reduce your shooting accuracy, as well as the lifetime of the individual components. as I'm sure broadheads would be pretty pricey for varmint dispatch.Crossbow maintenance is less demanding than taking care of a regular bow, which sometimes leads people to believe it’s of lower importance. Wasn't sure if they sell anything that might be better for this use other than maybe grinding the tips into a wadcutter blunt tip. I'm getting pass throughs with the standard off the shelf field target bolts that you can buy off of amazon. Recently been having coon and possum issues around the house at night (we're in the country and in the woods) - and am looking for better ammo for faster kills. Also - it's been strung for all that time, under tension, does that decrease the strength of the bow? ![]() I was worried about the string on the bow as it's easily 15 years old so I took it to the archery department at bass pro and the guys said that it wasn't in bad shape and didn't need replacing so wasn't sure if you just simply look for fraying or periodic replacement. I've long lost the string wax, but saw a mention here on the forum that I could use crisco on the rail / string / (serving?). Hey all - I've recently been plinking around with an OLD barnett trident pistol crossbow that I've had for many years. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |